ACPI error AE_NOT_FOUND with same motherboard replaced
Clash Royale CLAN TAG#URR8PPP up vote
2
down vote
favorite
My Shuttle barebone has broken down after two months. I sent it back to customer service who changed the motherboard and they also updated the BIOS (so BIOS version is not the same as on previous system).
Now when I connect my HDD, I see errors and system failed to boot :
[ 1.474485] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.474577] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
[ 1.482152] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.482296] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
/dev/sda5: recovering journal
/dev/sda5: clean, 419821/7331840 files , 2934231/29296640 blocks
Welcome to emergency mode! After logging in, type "journalctl -xb" to view system logs, "systemctl reboot" to reboot, "systemctl default" or ^D to try again to boot into default mode.
Press Enter for maintenance
(or press Control-D to continue):
I run Ubuntu 16.04 64-bit with linux kernel 4.13.0.37 and legacy BIOS.
Can anyone help me to solve this issue ?
Thank you.
16.04 boot bios
asked Apr 30 at 20:53
Céline Garel
114
add a comment |Â
up vote
2
down vote
favorite
My Shuttle barebone has broken down after two months. I sent it back to customer service who changed the motherboard and they also updated the BIOS (so BIOS version is not the same as on previous system).
Now when I connect my HDD, I see errors and system failed to boot :
[ 1.474485] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.474577] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
[ 1.482152] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.482296] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
/dev/sda5: recovering journal
/dev/sda5: clean, 419821/7331840 files , 2934231/29296640 blocks
Welcome to emergency mode! After logging in, type "journalctl -xb" to view system logs, "systemctl reboot" to reboot, "systemctl default" or ^D to try again to boot into default mode.
Press Enter for maintenance
(or press Control-D to continue):
I run Ubuntu 16.04 64-bit with linux kernel 4.13.0.37 and legacy BIOS.
Can anyone help me to solve this issue ?
Thank you.
16.04 boot bios
asked Apr 30 at 20:53
Céline Garel
114
add a comment |Â
up vote
2
down vote
favorite
up vote
2
down vote
favorite
My Shuttle barebone has broken down after two months. I sent it back to customer service who changed the motherboard and they also updated the BIOS (so BIOS version is not the same as on previous system).
Now when I connect my HDD, I see errors and system failed to boot :
[ 1.474485] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.474577] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
[ 1.482152] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.482296] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
/dev/sda5: recovering journal
/dev/sda5: clean, 419821/7331840 files , 2934231/29296640 blocks
Welcome to emergency mode! After logging in, type "journalctl -xb" to view system logs, "systemctl reboot" to reboot, "systemctl default" or ^D to try again to boot into default mode.
Press Enter for maintenance
(or press Control-D to continue):
I run Ubuntu 16.04 64-bit with linux kernel 4.13.0.37 and legacy BIOS.
Can anyone help me to solve this issue ?
Thank you.
16.04 boot bios
asked Apr 30 at 20:53
Céline Garel
114
My Shuttle barebone has broken down after two months. I sent it back to customer service who changed the motherboard and they also updated the BIOS (so BIOS version is not the same as on previous system).
Now when I connect my HDD, I see errors and system failed to boot :
[ 1.474485] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.474577] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
[ 1.482152] ACPI Error: [DSSP] Namespace lookup failure. AE_NOT_FOUND (20170531/psargs-364)
[ 1.482296] ACPI Error: Method parse/execution failed _SB.PCI0.SAT0.PRT2._GTF. AE_NO_FOUND (20170531/psparse-550)
/dev/sda5: recovering journal
/dev/sda5: clean, 419821/7331840 files , 2934231/29296640 blocks
Welcome to emergency mode! After logging in, type "journalctl -xb" to view system logs, "systemctl reboot" to reboot, "systemctl default" or ^D to try again to boot into default mode.
Press Enter for maintenance
(or press Control-D to continue):
I run Ubuntu 16.04 64-bit with linux kernel 4.13.0.37 and legacy BIOS.
Can anyone help me to solve this issue ?
Thank you.
16.04 boot bios
asked Apr 30 at 20:53
Céline Garel
114
edited May 1 at 7:16
asked Apr 30 at 20:53
Céline Garel
114
asked Apr 30 at 20:53
Céline Garel
114
asked Apr 30 at 20:53
Céline Garel
114
114
add a comment |Â
add a comment |Â
1 Answer
1
active
oldest
votes
up vote
0
down vote
The kernel drivers/ata/libata-acpi.c driver calls this ACPI method. The SATA (Serial ATA bus interface that connects to block devices) ACPI (Advanced Configuration and Power Interface) driver calls the _GTF control method in your firmware (BIOS) to re-initialize the drive. The _GTF method returns a bunch of ATA commands that are sent to the drive to restore the drive to the boot up defaults.
The error you are seeing is because your firmware does not have a _GTF method defined. This may be intentional as your hardware may not need these ATA commands, or it may be a bug because the BIOS vendor forgot to put them in. However, if your SATA drives are working correctly without error then it most probably is just not required and you need not worry about this kernel driver message.
answered May 1 at 8:13
Colin Ian King
11.4k13246
Many thanks for your detailled answer, I understand better how it works. I cannot boot system. Is there a fix that I can try to boot ?
– Céline Garel
May 1 at 8:29
Does your machine always break in the same way each time you reboot it?
– Colin Ian King
May 1 at 8:40
Yes, this is exactly what happens
– Céline Garel
May 1 at 8:56
I suspect the ' journalctl -xb' command may provide some more clues to why it is failing like this, but I'm not an expert in systemd, so perhaps somebody else can help you on that
– Colin Ian King
May 1 at 9:03
Have you fixed the problem? I have the same problem, but it just suddenly happened to start. @CélineGarel
– thigi
Jul 1 at 14:17
add a comment |Â
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
0
down vote
The kernel drivers/ata/libata-acpi.c driver calls this ACPI method. The SATA (Serial ATA bus interface that connects to block devices) ACPI (Advanced Configuration and Power Interface) driver calls the _GTF control method in your firmware (BIOS) to re-initialize the drive. The _GTF method returns a bunch of ATA commands that are sent to the drive to restore the drive to the boot up defaults.
The error you are seeing is because your firmware does not have a _GTF method defined. This may be intentional as your hardware may not need these ATA commands, or it may be a bug because the BIOS vendor forgot to put them in. However, if your SATA drives are working correctly without error then it most probably is just not required and you need not worry about this kernel driver message.
answered May 1 at 8:13
Colin Ian King
11.4k13246
Many thanks for your detailled answer, I understand better how it works. I cannot boot system. Is there a fix that I can try to boot ?
– Céline Garel
May 1 at 8:29
Does your machine always break in the same way each time you reboot it?
– Colin Ian King
May 1 at 8:40
Yes, this is exactly what happens
– Céline Garel
May 1 at 8:56
I suspect the ' journalctl -xb' command may provide some more clues to why it is failing like this, but I'm not an expert in systemd, so perhaps somebody else can help you on that
– Colin Ian King
May 1 at 9:03
Have you fixed the problem? I have the same problem, but it just suddenly happened to start. @CélineGarel
– thigi
Jul 1 at 14:17
add a comment |Â
up vote
0
down vote
The kernel drivers/ata/libata-acpi.c driver calls this ACPI method. The SATA (Serial ATA bus interface that connects to block devices) ACPI (Advanced Configuration and Power Interface) driver calls the _GTF control method in your firmware (BIOS) to re-initialize the drive. The _GTF method returns a bunch of ATA commands that are sent to the drive to restore the drive to the boot up defaults.
The error you are seeing is because your firmware does not have a _GTF method defined. This may be intentional as your hardware may not need these ATA commands, or it may be a bug because the BIOS vendor forgot to put them in. However, if your SATA drives are working correctly without error then it most probably is just not required and you need not worry about this kernel driver message.
answered May 1 at 8:13
Colin Ian King
11.4k13246
Many thanks for your detailled answer, I understand better how it works. I cannot boot system. Is there a fix that I can try to boot ?
– Céline Garel
May 1 at 8:29
Does your machine always break in the same way each time you reboot it?
– Colin Ian King
May 1 at 8:40
Yes, this is exactly what happens
– Céline Garel
May 1 at 8:56
I suspect the ' journalctl -xb' command may provide some more clues to why it is failing like this, but I'm not an expert in systemd, so perhaps somebody else can help you on that
– Colin Ian King
May 1 at 9:03
Have you fixed the problem? I have the same problem, but it just suddenly happened to start. @CélineGarel
– thigi
Jul 1 at 14:17
add a comment |Â
up vote
0
down vote
up vote
0
down vote
The kernel drivers/ata/libata-acpi.c driver calls this ACPI method. The SATA (Serial ATA bus interface that connects to block devices) ACPI (Advanced Configuration and Power Interface) driver calls the _GTF control method in your firmware (BIOS) to re-initialize the drive. The _GTF method returns a bunch of ATA commands that are sent to the drive to restore the drive to the boot up defaults.
The error you are seeing is because your firmware does not have a _GTF method defined. This may be intentional as your hardware may not need these ATA commands, or it may be a bug because the BIOS vendor forgot to put them in. However, if your SATA drives are working correctly without error then it most probably is just not required and you need not worry about this kernel driver message.
answered May 1 at 8:13
Colin Ian King
11.4k13246
The kernel drivers/ata/libata-acpi.c driver calls this ACPI method. The SATA (Serial ATA bus interface that connects to block devices) ACPI (Advanced Configuration and Power Interface) driver calls the _GTF control method in your firmware (BIOS) to re-initialize the drive. The _GTF method returns a bunch of ATA commands that are sent to the drive to restore the drive to the boot up defaults.
The error you are seeing is because your firmware does not have a _GTF method defined. This may be intentional as your hardware may not need these ATA commands, or it may be a bug because the BIOS vendor forgot to put them in. However, if your SATA drives are working correctly without error then it most probably is just not required and you need not worry about this kernel driver message.
answered May 1 at 8:13
Colin Ian King
11.4k13246
answered May 1 at 8:13
Colin Ian King
11.4k13246
answered May 1 at 8:13
Colin Ian King
11.4k13246
answered May 1 at 8:13
Colin Ian King
11.4k13246
11.4k13246
Many thanks for your detailled answer, I understand better how it works. I cannot boot system. Is there a fix that I can try to boot ?
– Céline Garel
May 1 at 8:29
Does your machine always break in the same way each time you reboot it?
– Colin Ian King
May 1 at 8:40
Yes, this is exactly what happens
– Céline Garel
May 1 at 8:56
I suspect the ' journalctl -xb' command may provide some more clues to why it is failing like this, but I'm not an expert in systemd, so perhaps somebody else can help you on that
– Colin Ian King
May 1 at 9:03
Have you fixed the problem? I have the same problem, but it just suddenly happened to start. @CélineGarel
– thigi
Jul 1 at 14:17
add a comment |Â
Many thanks for your detailled answer, I understand better how it works. I cannot boot system. Is there a fix that I can try to boot ?
– Céline Garel
May 1 at 8:29
Does your machine always break in the same way each time you reboot it?
– Colin Ian King
May 1 at 8:40
Yes, this is exactly what happens
– Céline Garel
May 1 at 8:56
I suspect the ' journalctl -xb' command may provide some more clues to why it is failing like this, but I'm not an expert in systemd, so perhaps somebody else can help you on that
– Colin Ian King
May 1 at 9:03
Have you fixed the problem? I have the same problem, but it just suddenly happened to start. @CélineGarel
– thigi
Jul 1 at 14:17
Many thanks for your detailled answer, I understand better how it works. I cannot boot system. Is there a fix that I can try to boot ?
– Céline Garel
May 1 at 8:29
Many thanks for your detailled answer, I understand better how it works. I cannot boot system. Is there a fix that I can try to boot ?
– Céline Garel
May 1 at 8:29
Does your machine always break in the same way each time you reboot it?
– Colin Ian King
May 1 at 8:40
Does your machine always break in the same way each time you reboot it?
– Colin Ian King
May 1 at 8:40
Yes, this is exactly what happens
– Céline Garel
May 1 at 8:56
Yes, this is exactly what happens
– Céline Garel
May 1 at 8:56
I suspect the ' journalctl -xb' command may provide some more clues to why it is failing like this, but I'm not an expert in systemd, so perhaps somebody else can help you on that
– Colin Ian King
May 1 at 9:03
I suspect the ' journalctl -xb' command may provide some more clues to why it is failing like this, but I'm not an expert in systemd, so perhaps somebody else can help you on that
– Colin Ian King
May 1 at 9:03
Have you fixed the problem? I have the same problem, but it just suddenly happened to start. @CélineGarel
– thigi
Jul 1 at 14:17
Have you fixed the problem? I have the same problem, but it just suddenly happened to start. @CélineGarel
– thigi
Jul 1 at 14:17
add a comment |Â
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f1030310%2facpi-error-ae-not-found-with-same-motherboard-replaced%23new-answer', 'question_page');
);
Post as a guest
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password