Slow Ubuntu Boot [ata2: SRST failed (errno=-16)] and [ata2: reset failed, giving up]

Clash Royale CLAN TAG#URR8PPP up vote
0
down vote
favorite
This Motherboard with a triple boot setup, booting in AHCI mode
Here is the relevant message (pulled from dmesg), note the long delay in timestamp between them:
[ 6.528119] ata2: link is slow to respond, please be patient (ready=-19)
[ 11.028120] ata2: SRST failed (errno=-16)
[ 16.540117] ata2: link is slow to respond, please be patient (ready=-19)
[ 21.040117] ata2: SRST failed (errno=-16)
[ 26.552117] ata2: link is slow to respond, please be patient (ready=-19)
[ 56.072118] ata2: SRST failed (errno=-16)
[ 56.072125] ata2: limiting SATA link speed to 1.5 Gbps
[ 61.104117] ata2: SRST failed (errno=-16)
[ 61.104142] ata2: reset failed, giving up
Seems to work fine on Windows. It's just an Ubuntu issue.
All my drives seem firmly connected, with no jumpers, most are SSD but some are IDE. I have like 6 drives. One is a Hackintosh (Mac GPT drive) and another is Windows. One SSD is connected via eSATA
I don't know if ata2 is the same as /dev/sdb but if it is, this may be interesting:
$ sudo fsck /dev/sdb
fsck from util-linux 2.31.1
e2fsck 1.44.1 (24-Mar-2018)
ext2fs_open2: Bad magic number in super-block
fsck.ext2: Superblock invalid, trying backup blocks...
fsck.ext2: Bad magic number in super-block while trying to open /dev/sdb
The superblock could not be read or does not describe a valid ext2/ext3/ext4
filesystem. If the device is valid and it really contains an ext2/ext3/ext4
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
or
e2fsck -b 32768 <device>
Found a gpt partition table in /dev/sdb
A commentary on the cause: https://www.redhat.com/archives/rhl-list/2006-October/msg03892.html
Because it's a GPT hackintosh drive:
$ sudo gdisk /dev/sdb -l
GPT fdisk (gdisk) version 1.0.3
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Disk /dev/sdb: 1953525168 sectors, 931.5 GiB
Model: ST31000524AS
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 384E6D96-A1EE-4D32-8FE5-14B63E4BF049
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 1953525134
Partitions will be aligned on 8-sector boundaries
Total free space is 262157 sectors (128.0 MiB)
Verify disk passes:
$ sudo gdisk /dev/sdb
$ v
No problems found. 262157 free sectors (128.0 MiB) available in 2
segments, the largest of which is 262151 (128.0 MiB) in size.
boot hard-drive sata
add a comment |Â
up vote
0
down vote
favorite
This Motherboard with a triple boot setup, booting in AHCI mode
Here is the relevant message (pulled from dmesg), note the long delay in timestamp between them:
[ 6.528119] ata2: link is slow to respond, please be patient (ready=-19)
[ 11.028120] ata2: SRST failed (errno=-16)
[ 16.540117] ata2: link is slow to respond, please be patient (ready=-19)
[ 21.040117] ata2: SRST failed (errno=-16)
[ 26.552117] ata2: link is slow to respond, please be patient (ready=-19)
[ 56.072118] ata2: SRST failed (errno=-16)
[ 56.072125] ata2: limiting SATA link speed to 1.5 Gbps
[ 61.104117] ata2: SRST failed (errno=-16)
[ 61.104142] ata2: reset failed, giving up
Seems to work fine on Windows. It's just an Ubuntu issue.
All my drives seem firmly connected, with no jumpers, most are SSD but some are IDE. I have like 6 drives. One is a Hackintosh (Mac GPT drive) and another is Windows. One SSD is connected via eSATA
I don't know if ata2 is the same as /dev/sdb but if it is, this may be interesting:
$ sudo fsck /dev/sdb
fsck from util-linux 2.31.1
e2fsck 1.44.1 (24-Mar-2018)
ext2fs_open2: Bad magic number in super-block
fsck.ext2: Superblock invalid, trying backup blocks...
fsck.ext2: Bad magic number in super-block while trying to open /dev/sdb
The superblock could not be read or does not describe a valid ext2/ext3/ext4
filesystem. If the device is valid and it really contains an ext2/ext3/ext4
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
or
e2fsck -b 32768 <device>
Found a gpt partition table in /dev/sdb
A commentary on the cause: https://www.redhat.com/archives/rhl-list/2006-October/msg03892.html
Because it's a GPT hackintosh drive:
$ sudo gdisk /dev/sdb -l
GPT fdisk (gdisk) version 1.0.3
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Disk /dev/sdb: 1953525168 sectors, 931.5 GiB
Model: ST31000524AS
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 384E6D96-A1EE-4D32-8FE5-14B63E4BF049
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 1953525134
Partitions will be aligned on 8-sector boundaries
Total free space is 262157 sectors (128.0 MiB)
Verify disk passes:
$ sudo gdisk /dev/sdb
$ v
No problems found. 262157 free sectors (128.0 MiB) available in 2
segments, the largest of which is 262151 (128.0 MiB) in size.
boot hard-drive sata
add a comment |Â
up vote
0
down vote
favorite
up vote
0
down vote
favorite
This Motherboard with a triple boot setup, booting in AHCI mode
Here is the relevant message (pulled from dmesg), note the long delay in timestamp between them:
[ 6.528119] ata2: link is slow to respond, please be patient (ready=-19)
[ 11.028120] ata2: SRST failed (errno=-16)
[ 16.540117] ata2: link is slow to respond, please be patient (ready=-19)
[ 21.040117] ata2: SRST failed (errno=-16)
[ 26.552117] ata2: link is slow to respond, please be patient (ready=-19)
[ 56.072118] ata2: SRST failed (errno=-16)
[ 56.072125] ata2: limiting SATA link speed to 1.5 Gbps
[ 61.104117] ata2: SRST failed (errno=-16)
[ 61.104142] ata2: reset failed, giving up
Seems to work fine on Windows. It's just an Ubuntu issue.
All my drives seem firmly connected, with no jumpers, most are SSD but some are IDE. I have like 6 drives. One is a Hackintosh (Mac GPT drive) and another is Windows. One SSD is connected via eSATA
I don't know if ata2 is the same as /dev/sdb but if it is, this may be interesting:
$ sudo fsck /dev/sdb
fsck from util-linux 2.31.1
e2fsck 1.44.1 (24-Mar-2018)
ext2fs_open2: Bad magic number in super-block
fsck.ext2: Superblock invalid, trying backup blocks...
fsck.ext2: Bad magic number in super-block while trying to open /dev/sdb
The superblock could not be read or does not describe a valid ext2/ext3/ext4
filesystem. If the device is valid and it really contains an ext2/ext3/ext4
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
or
e2fsck -b 32768 <device>
Found a gpt partition table in /dev/sdb
A commentary on the cause: https://www.redhat.com/archives/rhl-list/2006-October/msg03892.html
Because it's a GPT hackintosh drive:
$ sudo gdisk /dev/sdb -l
GPT fdisk (gdisk) version 1.0.3
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Disk /dev/sdb: 1953525168 sectors, 931.5 GiB
Model: ST31000524AS
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 384E6D96-A1EE-4D32-8FE5-14B63E4BF049
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 1953525134
Partitions will be aligned on 8-sector boundaries
Total free space is 262157 sectors (128.0 MiB)
Verify disk passes:
$ sudo gdisk /dev/sdb
$ v
No problems found. 262157 free sectors (128.0 MiB) available in 2
segments, the largest of which is 262151 (128.0 MiB) in size.
boot hard-drive sata
This Motherboard with a triple boot setup, booting in AHCI mode
Here is the relevant message (pulled from dmesg), note the long delay in timestamp between them:
[ 6.528119] ata2: link is slow to respond, please be patient (ready=-19)
[ 11.028120] ata2: SRST failed (errno=-16)
[ 16.540117] ata2: link is slow to respond, please be patient (ready=-19)
[ 21.040117] ata2: SRST failed (errno=-16)
[ 26.552117] ata2: link is slow to respond, please be patient (ready=-19)
[ 56.072118] ata2: SRST failed (errno=-16)
[ 56.072125] ata2: limiting SATA link speed to 1.5 Gbps
[ 61.104117] ata2: SRST failed (errno=-16)
[ 61.104142] ata2: reset failed, giving up
Seems to work fine on Windows. It's just an Ubuntu issue.
All my drives seem firmly connected, with no jumpers, most are SSD but some are IDE. I have like 6 drives. One is a Hackintosh (Mac GPT drive) and another is Windows. One SSD is connected via eSATA
I don't know if ata2 is the same as /dev/sdb but if it is, this may be interesting:
$ sudo fsck /dev/sdb
fsck from util-linux 2.31.1
e2fsck 1.44.1 (24-Mar-2018)
ext2fs_open2: Bad magic number in super-block
fsck.ext2: Superblock invalid, trying backup blocks...
fsck.ext2: Bad magic number in super-block while trying to open /dev/sdb
The superblock could not be read or does not describe a valid ext2/ext3/ext4
filesystem. If the device is valid and it really contains an ext2/ext3/ext4
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
or
e2fsck -b 32768 <device>
Found a gpt partition table in /dev/sdb
A commentary on the cause: https://www.redhat.com/archives/rhl-list/2006-October/msg03892.html
Because it's a GPT hackintosh drive:
$ sudo gdisk /dev/sdb -l
GPT fdisk (gdisk) version 1.0.3
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Disk /dev/sdb: 1953525168 sectors, 931.5 GiB
Model: ST31000524AS
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 384E6D96-A1EE-4D32-8FE5-14B63E4BF049
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 1953525134
Partitions will be aligned on 8-sector boundaries
Total free space is 262157 sectors (128.0 MiB)
Verify disk passes:
$ sudo gdisk /dev/sdb
$ v
No problems found. 262157 free sectors (128.0 MiB) available in 2
segments, the largest of which is 262151 (128.0 MiB) in size.
boot hard-drive sata
edited May 26 at 17:27
asked May 24 at 20:55
Jonathan
1,10421326
1,10421326
add a comment |Â
add a comment |Â
active
oldest
votes
active
oldest
votes
active
oldest
votes
active
oldest
votes
active
oldest
votes
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f1039982%2fslow-ubuntu-boot-ata2-srst-failed-errno-16-and-ata2-reset-failed-giving%23new-answer', 'question_page');
);
Post as a guest
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e)
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom))
StackExchange.using('gps', function() StackExchange.gps.track('embedded_signup_form.view', location: 'question_page' ); );
$window.unbind('scroll', onScroll);
;
$window.on('scroll', onScroll);
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password